Updating...

Flexiride Half Torsion Axles: How to Choose Capacity, Set the Starting Angle and Mount Them

A half torsion axle is a short, bolt-on rubber torsion suspension for one wheel. A left half and a right half make one complete axle, so you can mount the suspension at the frame rails and leave the middle of the trailer open. That is why half axles are popular on small boat trailers, utility trailers, cargo trailers and any trailer that needs a low center of gravity at the center of the frame.

This guide covers the Flexiride half axles Southwest Wheel carries, from 425 lb. to 7,000 lb. per pair: how the two styles differ, how to pick the capacity, what the starting angle does to ride and frame height, and how Flexiride says the units must be mounted. The information comes from The Universal Group's Flexiride half axle catalog, instruction sheet, mounting data, starting angle drawings and FAQ. Use it as an overview, not a substitute for the instructions supplied with your axle.

Key takeaways

  • Capacity is for the pair. A 3,500 lb. pair is one left and one right half, and each half carries 1,750 lbs. Our listings state capacity by the pair.
  • Derate for a tandem, and never use three. Flexiride ratings are for single axle use on paved roads. For tandem use, Flexiride says to derate 20 percent, and it does not allow triple axle setups because the axles are independent and do not share load.
  • Normal starting angle is about 24 degrees down. On the larger cartridge half axles, Flexiride strongly recommends the 24 degree down starting angle, which puts the arm near horizontal at rated load for the best ride. The small 425 lb. to 935 lb. units use a 30 degree down normal setting.
  • Bolt it to a fully supported base plate. Every bolt hole must be used, the plate must be supported along its full length, and there must be no welding on the half axle itself. Welding damages the rubber and voids the warranty.
  • Keep oil and grease off the rubber. Flexiride says grease, oil and fuel damage the rubber. Clean the unit with detergent and water only.

Terms used in this guide

  • Half axle (torsion half axle): A one-wheel torsion suspension unit with its own mounting bracket. Two halves, left and right, make one axle.
  • Torsion arm: The arm that holds the spindle. As the wheel moves up, the arm twists rubber inside the housing, and the rubber springs it back.
  • Starting angle: The angle of the torsion arm from horizontal with no load on it. "Down" means the spindle end sits below the pivot.
  • Free position: Where the arm rests with no weight on it.
  • Adjustable arm: An arm on a splined or serrated shaft that can be moved to a different starting angle. Flexiride marks adjustable small units with an S after the size (for example 425S).
  • Welded arm: A fixed arm that cannot be re-angled. Our category pages call these stationary.
  • Base plate: A flat steel plate welded to the trailer frame or a cross member. The half axle bolts to it.
  • Hub face offset: How far the hub face sits outboard of the half axle bracket.

Two styles of Flexiride half axle

Flexiride half axles come in two body styles. Flexiride calls the small style British and the larger style Cartridge.

  • Small rubber-in-tube style, 425 lb. to 935 lb. per pair: A light bolt-on unit with a short arm and a straight spindle. The 425 lb. size always has an adjustable arm. The 550 lb. and 935 lb. sizes come with either a welded (stationary) arm or an adjustable arm. Flexiride's brochure says the compact rubber cartridge allows the narrowest track centers in the industry.
  • Cartridge style with brake flange, 1,400 lb. to 7,000 lb. per pair: A bracket housing a press-fit rubber cartridge, with a one-piece forged drop spindle arm and a brake flange. The arm sits on a 60-spline shaft held by a pinch bolt, so the starting angle can be changed and the arm can be removed. Flexiride lists these units as built with camber.

Flexiride says its rubber cartridge damps vibration on its own, so no shock absorbers are required, and that each wheel moves independently with no equalizers, shackles or hangers to wear out.

Flexiride half axles Southwest Wheel carries

Every half axle below is sold as a left and right pair. Pairs with hubs include lug nuts; mounting bolts are not included, and parts arrive loose and require assembly. Pairs listed without hubs are the bare half axles. Base plates are sold individually, so order two per pair.

Capacity per pair Style and arm Without hubs With hubs With electric brakes Base plate
425 lb. Small style, adjustable arm 425S pair 4 on 4 in., 5 on 4.5 in. - FS30-2
550 lb. stationary Small style, welded arm - 4 on 4 in., 5 on 4.5 in. - FS30-3
550 lb. adjustable Small style, adjustable arm - 4 on 4 in., 5 on 4.5 in. - FS30-3
935 lb. stationary Small style, welded arm - 4 on 4 in., 5 on 4.5 in. - FS30-3
935 lb. adjustable Small style, adjustable arm - 4 on 4 in., 5 on 4.5 in. - FS30-3
1,400 lb. Cartridge, adjustable arm 1400B pair 4 on 4 in., 5 on 4.5 in. - FS30-6
2,000 lb. Cartridge, adjustable arm 2000B pair 4 on 4 in., 5 on 4.5 in. - FS30-6
3,500 lb. Cartridge, adjustable arm 3500B pair 5 on 4.5 in., 5 on 4.75 in., 5 on 5 in., 5 on 5.5 in., 6 on 5.5 in. 5 on 4.5 in., 5 on 4.75 in., 5 on 5 in., 5 on 5.5 in., 6 on 5.5 in. FHP-35
5,200 lb. Cartridge, adjustable arm 5200B pair 6 on 5.5 in. 6 on 5.5 in. Not listed
7,000 lb. Cartridge, adjustable arm 7000B pair 8 on 6.5 in. 8 on 6.5 in. Not listed

Our 3,500 lb. pair with 5 on 4.5 in. hubs and brakes is listed with 10 in. electric drum brakes, the same size Flexiride lists for its 3,500 lb. braked pair. Flexiride's catalog lists base plates for the 425 lb. through 3,500 lb. sizes only, so plan the frame mounting for a 5,200 lb. or 7,000 lb. pair with your trailer builder. The bare 3,500 lb. pair listing also shows matching electric and hydraulic brake kit options; for how to choose one, see How to Choose a TruRyde Drum Brake Kit.

How to pick the capacity

Flexiride's published ratings are based on the maximum loading of single axle applications used on paved roads and highways. For half axles, count each left and right pair as one axle.

  1. Find the gross vehicle weight. Flexiride defines GVW as the empty trailer weight plus the weight of the intended cargo.
  2. Decide single or tandem. For a tandem, Flexiride says to derate 20 percent. Its design notes say the same thing another way: apply a 1.25 factor to the static load for dynamic loading.
  3. Pick the next size up. Flexiride's example: a 10,000 lb. GVW tandem needs at least 6,250 lbs. per axle (10,000 x 1.25, divided by 2), so the matching size is 7,000 lbs.

A few limits apply to every size:

  • No triple axles. Flexiride completely discourages triple applications, even derated. Over driveway entries, railroad crossings or speed bumps, the whole load can land on one axle.
  • Built for the road. Flexiride's half axle instruction sheet says the product is not recommended for off-road applications. If your trailer will see rough or off-road use anyway, Flexiride's FAQ says to derate the axle capacity by 10 percent, so choose a size with room to spare.
  • Half axles do not add capacity. Flexiride says changing to half axles will not increase the capacity of the trailer, and that structural alterations to the half axle are not allowed and void the warranty.
  • Match the wheels and tires. The wheels and tires must be rated for the load too. See Choosing Trailer Axle Capacity: Hitch Weight, GAWR, Wheels and Tires.

Starting angle: what it is and how to set it

The starting angle sets where the torsion arm sits with no load. Weight on the trailer then rotates the arm up. Flexiride says ride is best when the arm is at or near horizontal at rated load, and that arms working above horizontal give a stiffer ride. The starting angle also changes frame height, as covered in the next section.

Cartridge half axles: 1,400 lb. to 7,000 lb.

  • Normal setting: Flexiride strongly recommends the normal 24 degree down starting angle except in special circumstances. Its drawing shows the arm installed at 24 degrees down, running horizontal at full load and returning to about 22 degrees down in the free position. Flexiride's half axle instructions say the adjustable arm comes pre-adjusted to 22 degrees down.
  • Steps: The arm sits on a 60-spline shaft and moves in 6 degree steps, with alignment marks on the shaft and arm for reference.
  • Limits: Do not set the arm higher than 10 degrees up or lower than 45 degrees down. Flexiride calls 10 degrees up the maximum up setting, with reduced compliance, and says improper adjustment voids the warranty.
  • Lower settings sit lower. At a 10 degree down start, Flexiride's drawing shows the arm running 12.5 degrees up at full load. At 0 degrees it runs 25 degrees up.

To change the angle, Flexiride says to remove the cross bolt (pinch bolt), move the arm to the new spline position and re-tighten. The nut and washer always go on the ground side. Pinch bolt torque from Flexiride's drawings:

Half axle size Pinch bolt (SAE grade 5) Steel bolt, oiled Cadmium plated
1,400 lb. and 2,000 lb. 1/2-20 UNF x 3.25 in. 85 ft-lb minimum 70 ft-lb minimum
3,500 lb. 5/8-18 UNF x 3-1/2 in. 170 ft-lb minimum 140 ft-lb minimum
5,200 lb. and 7,000 lb. 7/8-14 UNF x 5.25 in. 475 ft-lb minimum 380 ft-lb minimum

Small half axles: 425 lb. to 935 lb.

  • Normal setting: Flexiride's normal (best) starting angle for these units is 30 degrees down.
  • Adjustable arms (425S, 550S and 935S) sit on a 32-serration shaft and move in 11.25 degree steps. Flexiride's drawings also show 10 degrees down, 0 degrees and 10 degrees up settings, with 10 degrees up as the maximum.
  • Welded arms (550 and 935 stationary) cannot be changed. Flexiride says to use the normal 30 degree down diagram for them.
  • Cross bolt torque: 5/16-24 x 2.50 in. at 19 to 24 ft-lb on the 425S; 3/8-24 x 2.50 in. at 35 to 45 ft-lb on the 550S and 935S.

Starting angle and frame height

Flexiride's frame height data sheet gives a simple formula for the loaded distance from the ground to the trailer frame:

Frame height at load = tire static loaded radius + H - ht

  • Static loaded radius (SLR): The distance from the wheel center to the ground with the tire under load, from the tire maker.
  • H: A fixed dimension for each size. Flexiride lists 0.80 in. for 425 lb., 0.88 in. for 550 lb. and 935 lb., 1.56 in. for 1,400 lb. and 2,000 lb., 1.88 in. for 3,500 lb., and 2.50 in. for 5,200 lb. and 7,000 lb.
  • ht: How far the spindle sits above horizontal at load. It is zero at the normal starting angle, because the arm runs horizontal at load, and it grows as the starting angle moves up.

Flexiride's worked values for two cartridge sizes:

Half axle and tire 22 degrees down 10 degrees down 0 degrees 10 degrees up
2,000 lb., 4.80-12 tire (SLR 9.5 in.) 11.06 in. 10.09 in. 9.15 in. 8.73 in.
3,500 lb., 7.00-15 tire (SLR 13.7 in.) 15.58 in. 14.61 in. 13.67 in. 13.25 in.

Moving from the normal setting to 10 degrees up drops this 3,500 lb. example by about 2.3 in. Flexiride adds three more height notes:

  • The trailer frame should be level, and Flexiride says trailers with its axles must be towed level so the axles load evenly.
  • Allow 3 in. of fender clearance over the tire at full load.
  • Because Flexiride units use drop spindles, use a wheel and tire large enough to keep the axle parts off the ground if a tire goes flat.

For more on deck height, see Drop Axle vs Straight Axle: Deck Height Guide.

How Flexiride half axles must be mounted

Half axles do not have a full axle tube acting as an extra cross member, so Flexiride says frame support is even more critical than with a full axle. Its half axle instructions list these rules:

  1. Measure before you remove the old axle. Record the distance from the hitch point to the wheel centers and keep it, so the trailer's balance stays the same.
  2. Add a cross member if needed. Unless one is already there, add a cross member to the frame for welding the base plates.
  3. Support the whole plate. The half axle must be bolted, using all bolt holes, to a base plate that fully supports it, and the base plate must be supported along its entire length. If the plates are welded to a new cross member, the cross member must reach the outside edge of the plate.
  4. Never weld the half axle. Any welding on the half axle critically alters the rubber and bonding adhesive and voids the warranty. Flexiride also says not to galvanize or powder coat a finished unit, because the inner parts are heat sensitive.
  5. Use grade 5 fine thread bolts with lock washers to attach the half axle to the base plate or frame.
  6. Align the wheels. Flexiride says each axle must be square to the trailer centerline within one half degree, and on a tandem the axles must be parallel within 1/16 in. at the wheel centers.

Mounting data from Flexiride's half axle sheets:

Size per pair Hub face offset Mounting bolts per half Arm centers Bearings, inner / outer
425 lb. 4.13 in. 6, 5/16-24 3.50 in. L44643 / L44643
550 lb. 4.13 in. 6, 5/16-24 4.50 in. L44643 / L44643
935 lb. 4.13 in. 6, 5/16-24 3.50 in. L44643 / L44643
1,400 lb. 5.91 in. 6, 3/8-24 4.50 in. L44649 / L44649
2,000 lb. 5.91 in. 6, 3/8-24 4.50 in. L44649 / L44649
3,500 lb. 6.44 in. 8, 1/2-20 4.50 in. L68149 / L44649

Flexiride's mounting bolt torque: 18 to 20 ft-lb for 5/16-24 bolts, 30 to 35 ft-lb for 3/8-24 bolts (1,400 lb. and 2,000 lb. sizes) and 75 to 85 ft-lb for 1/2-20 bolts. The mounting data sheet does not cover the 5,200 lb. and 7,000 lb. sizes. For those, Flexiride's data sheet shows a 25580 inner bearing and a 1.25 in. outer bearing seat that takes an LM67048, 15123 or 14125A cone depending on the hub, so read the numbers on your bearings before ordering.

On aluminum frames, Flexiride warns that bolt clamping loads can make the aluminum yield and the axle loosen, and that any non-metal spacer used against galvanic corrosion must hold up under high clamp loads.

Camber and alignment

Flexiride half axles are built with camber. The cartridge drawings show the spindle shaft exiting the end of the tube at a 1.5 degree down angle, and Flexiride does not allow structural alterations to the unit. Flexiride says proper alignment results in better road handling. If you see uneven tire wear, see Trailer Axle Alignment and Uneven Tire Wear.

Hub, bearing and rubber care

  • Grease the bearings every 12 months or 12,000 miles. Flexiride specifies a lithium complex, NLGI No. 2 grease and warns not to mix it with barium, calcium, clay or polyurea thickeners.
  • Bearing adjustment: Snug the spindle nut to about 50 ft-lb while turning the hub, back it off, set it finger tight to the nearest slot and lock it. Flexiride allows end play up to .012 in. Full steps are in Trailer Hub Bearing Adjustment and Grease, Step by Step.
  • Lubricated spindles: Remove the rubber plug from the grease cap, grease through the fitting while turning the hub until clean grease appears, then wipe off the excess and replace the plug.
  • Heavy sizes: Flexiride says to use a hub puller to remove the drum on 5,200 lb. and 7,000 lb. half axles.
  • Protect the rubber: Keep grease, oil and fuel off the half axle. Clean it with detergent and water only. If a bushing squeaks, Flexiride suggests silicone spray, never a petroleum product.
  • Inspect yearly. Flexiride says to inspect trailer axles once a year and boat trailer axles twice a year. Before every trip, check tire pressure and wheel nut torque, do not exceed the rated load, and keep 60 percent of the load ahead of the axle.

For replacement cones and cups by number, see How to Read a Tapered Roller Bearing Number and Match the Cup and Cone on a Trailer Hub.

Checklist before ordering

  • Gross vehicle weight, and whether the trailer is single or tandem (never triple).
  • Capacity per pair after the 20 percent tandem derate.
  • Small style or cartridge style, and welded or adjustable arm.
  • Bolt pattern of your wheels, and whether you need brakes.
  • Starting angle and target frame height, using your tire's static loaded radius.
  • Two base plates per pair (425 lb. to 3,500 lb.) and a cross member that fully supports them.
  • Grade 5 fine thread mounting bolts with lock washers (not included).
  • Hitch-to-wheel-center distance measured from the old axle.
  • Fender clearance of 3 in. over the tire at full load.

Safety note

Suspension and wheel ends are safety equipment. Flexiride warns that improper support of a half axle, or any welding on it, will cause failure and may result in injury, and that losing a wheel end while moving can lead to an accident. Follow the instructions supplied with your half axles and have the finished installation checked by a qualified trailer technician before towing. Southwest Wheel sells new parts and does not provide installation service.

FAQ

Is the capacity per half axle or per pair?

Per pair. A left half and a right half make one axle, and our listings rate the pair. Each half carries half the load; the label on a 3,500 lb. half axle reads 1,750 lbs.

Can I use Flexiride half axles on a tandem trailer?

Yes, with a 20 percent derate. Do not use three axles: Flexiride says its independent axles cannot share load like an equalized leaf spring set.

Can I weld the half axle to the frame?

No. Weld the base plate to the frame or a cross member, then bolt the half axle to the plate using every hole. Welding on the half axle damages the rubber and voids the warranty.

What starting angle should I use?

For the cartridge sizes, Flexiride strongly recommends about 24 degrees down. For the small 425 lb. to 935 lb. sizes, the normal setting is 30 degrees down. Use other settings only to reach a specific frame height, and never go past 10 degrees up.

Do half axles need shock absorbers?

Flexiride says no. The rubber cartridge damps vibration on its own.

Can I replace just the spindle arm or the rubber cartridge?

On the 1,400 lb. and larger sizes, yes, the spindle arm is adjustable and replaceable. Remove the pinch bolt and the arm slides off the splined shaft. Southwest Wheel sells replacement spindle arms for these sizes, but they are not listed online yet, so call us with your axle capacity and starting angle. The rubber cartridge is installed by Flexiride's licensed manufacturers, so a worn cartridge, or a worn arm on the smaller sizes, means a new half axle.

Can I galvanize or paint my half axles?

Flexiride says not to galvanize or powder coat a finished axle, because the rubber and inner parts are heat sensitive.

How do half axles compare with a Dexter Torflex axle?

Both are rubber torsion suspensions. A full torsion axle uses a tube across the frame, while half axles bolt on at each side and leave the center open. For full axles, see How Dexter Torflex Axles Work, and How to Pick a Replacement.

References

  • The Universal Group, LLC. Flexiride Half Axle catalog (No. FHA 002 02-18).
  • The Universal Group. Instruction Sheet for Flexiride Half Axles (Engineering Instruction EI-0010, Revision A1, 06.01.22).
  • The Universal Group Corp. Flexiride Half Axle System Suspension Mounting Data.
  • The Universal Group Corp. Flexiride Cartridge Axles Data Sheet, and Cartridge Axles Data Sheet: Frame Height From Tire SLR.
  • The Universal Group. Flexiride starting angle drawings: adjustable arm starting angles, cartridge half axle starting angles, and British-style starting angles.
  • The Universal Group. Flexiride half axle drawings: 425S, 550, 550S, 935, 935S, 1400B, 2000B, 3500B and 5200B/7000B.
  • The Universal Group Corp. Flexiride Frequently Asked Questions.
  • The Universal Group. Things to Keep in Mind When You Design Your Flexiride Equipped Trailer.
  • The Universal Group, LLC. Flexiride Rubber Torsion Axles brochure (No. F002 02-18).

Related guides

Find the right Flexiride half axles for your trailer

Have your trailer's gross weight, single or tandem setup, wheel bolt pattern, brake needs and target frame height ready when you shop or call. Southwest Wheel has supplied trailer parts for 107 years, and we can help you match a half axle pair and base plates to your build.

Shop Torsion Half Axles

Need a full-width Flexiride torsion axle instead? See all Flexiride products. Mounting a pair? Add the matching 3,500 lb. base plate, 1,400 lb. and 2,000 lb. base plate, 550 lb. and 935 lb. base plate or 425 lb. base plate.

Call Southwest Wheel at 1-800-866-3336.

Southwest Wheel - Your Trailers Best Friend Since 1919.

 
Sign Up For Special Offers and News!

Get 5% off your first purchase , information on newest offers, and useful tips on how to get the most out of our services.

Valid once per customer on first purchase only. Not combinable with other offers or past orders.
 
Loading...