How to Read a Tapered Roller Bearing Number and Match the Cup and Cone on a Trailer Hub
Every trailer hub with standard bearings has two tapered roller bearings: a larger inner bearing behind the hub and a smaller outer bearing under the spindle nut. Each bearing is a matched pair of parts, a cone with rollers and a cup pressed into the hub, and each part carries its own number. Order by the wrong number and the bearing will not slide onto the spindle, will not seat in the hub, or will fit loosely and fail early.
This guide shows where to find the number on a trailer bearing, how a cone number and a cup number go together, which bearings fit common trailer axles from 2,000 lb. through 8,000 lb., and what changed on Dexter 4,400 lb. and 5,200 lb. hubs in the last few years. It also covers heavy duty axles, how to measure when the number is gone, and which kits include the cups.
Key takeaways
- A bearing is two parts with two numbers. The cone (the part with the rollers) has one number and the cup (also called the race) has another. Both must match the hub and spindle.
- The spindle picks the cone and the hub picks the cup. The cone's bore has to fit the spindle's bearing seat, and the cup's outside diameter has to fit the hub.
- Replace them together. Dexter's service manual says bearings must always be replaced in sets of a cone and a cup.
- Inner and outer are usually different sizes. On most trailer hubs the inner bearing is larger than the outer bearing, so you need two numbers for each hub.
- Check the date on 4,400 lb. and 5,200 lb. Dexter hubs. Dexter Product Bulletin 463 changed the 4,400 lb. bearings in June 2022, and Product Bulletin 479 moved 5,200 lb. production axles to a different outer bearing in 2023.
Terms used in this guide
- Tapered roller bearing: A bearing with cone shaped rollers that run between a cone and a cup. Trailer hubs use two of them, facing each other.
- Cone: The inner ring with the rollers and the cage that holds them. It slides onto the spindle. Many catalogs and listings simply call the cone "the bearing."
- Cup (race): The smooth outer ring the rollers run on. It is pressed into the hub. TRP and Dexter say cup; Lippert, TruRyde and many listings say race.
- Cone bore: The inside diameter of the cone. It must match the bearing seat on the spindle.
- Cup OD: The outside diameter of the cup. It must match the bearing bore in the hub.
- Inner bearing: The bearing closest to the axle, behind the hub. The grease seal sits behind it.
- Outer bearing: The bearing closest to the spindle nut and grease cap.
- Industry number: The bearing number used across brands, for example L68149. Southwest Wheel lists TruRyde and Timken cones and cups under these numbers.
Where to find the number on a trailer bearing
Clean the old parts first. Dexter's service manual says to wash all grease and oil from the bearing cone with a suitable solvent and dry it with a clean, lint-free cloth. Never spin a bearing with compressed air; Dexter warns this can damage it.
- On the cone: The number is stamped or etched on the wide face of the cone or cage. Turn the cone over and look on both faces if you do not see it right away.
- On the cup: The number is on the thin edge face of the cup. You can often read it with the cup still in the hub by looking into the hub with a light after the grease is cleaned out.
Write down every letter and digit exactly as it appears, including letters in front of the number and at the end. L44649 and L44643 are different cones, and 14125A is the full number for that cone, letter included.
How cone and cup numbers go together
A cone and its cup share a family, but the numbers are not the same. On many trailer bearings the two numbers match except for the last two digits, and the cone has the higher ending. Other pairs look less alike. Here are the pairs used on trailer axles from 2,000 lb. through 8,000 lb., from the Dexter bearing replacement chart and the TRP and Lippert catalogs:
| Cone number | Matching cup number | How the numbers line up |
|---|---|---|
| L44649 | L44610 | Same except the last two digits |
| L44643 | L44610 | A smaller bore cone for the same cup |
| L68149 | L68111 | Same except the last two digits |
| LM67048 | LM67010 | Same except the last two digits |
| 25580 | 25520 | Same first three digits |
| 15123 | 15245 | Only the first two digits match |
| 14125A | 14276 | Only the first two digits match |
| 02475 | 02420 | Same first three digits |
Because some pairs barely look related, do not guess a cup number from a cone number. Use a chart like the ones below, or read the number off the old cup.
One cup can also take more than one cone. The L44610 cup fits both the L44643 cone (1.000 in. bore) and the L44649 cone (1.0625 in. bore). Dexter's own 2,500 lb. and 2,700 lb. idler hub kits use the same hub with either cone, depending on the axle. That is why the spindle, not the hub, decides the cone.
Cone and cup sizes for 2,000 lb. to 8,000 lb. trailer axles
These are the cone bores and cup outside diameters listed in the 2026 TRP catalog, and they agree with the Lippert Premium Axle Parts catalog. Southwest Wheel carries each one in TruRyde and, for all but one, in Timken.
| Cone / cup | Cone bore | Cup OD | Common trailer use | TruRyde | Timken |
|---|---|---|---|---|---|
| L44643 / L44610 | 1.0000 in. | 1.9800 in. | Both ends of a 2,000 lb. hub on a 1 in. straight spindle | Cone, cup | Cone, cup |
| L44649 / L44610 | 1.0625 in. | 1.9800 in. | Both ends of a 2,000 lb. hub on a 1-1/16 in. spindle; outer bearing on 2,800 lb. to 4,000 lb. hubs | Cone, cup | Cone, cup |
| L68149 / L68111 | 1.3775 in. | 2.3612 in. | Inner bearing on 3,500 lb. to 4,400 lb. hubs; both ends on a Dexter 4,400 lb. hub after June 2022 | Cone, cup | Cone, cup |
| LM67048 / LM67010 | 1.2500 in. | 2.3280 in. | Inner bearing on 2,800 lb. and 3,000 lb. hubs; outer bearing on older 4,400 lb. and 5,200 lb. hubs | Cone, cup | Cup; for the cone, use the TruRyde LM67048 |
| 25580 / 25520 | 1.7500 in. | 3.2650 in. | Inner bearing on 5,200 lb. to 8,000 lb. hubs | Cone, cup | Cone, cup |
| 15123 / 15245 | 1.2500 in. | 2.4409 in. | Outer bearing on 6,000 lb. 6 bolt hubs, 7,000 lb. 5 bolt demountable hubs and Dexter 5,200 lb. axles built since 2023 | Cone, cup | Cone, cup |
| 14125A / 14276 | 1.2500 in. | 2.7170 in. | Outer bearing on 6,000 lb. and 7,000 lb. 8 bolt hubs | Cone, cup | Cone, cup |
| 02475 / 02420 | 1.2500 in. | 2.6875 in. | Outer bearing on 7,200 lb. and 8,000 lb. hubs | Cone, cup | Cone, cup |
Browse every size in Bearings for Trailer Hubs and Drums and Races for Trailer Hubs and Drums, or shop the Timken line in Timken Bearings and Timken Races.
Which bearings fit which Dexter trailer hub
Dexter's bearing replacement chart in its 2,000 to 8,000 lbs. service manual lists the inner and outer bearings by brake size, bolt count and axle capacity. The table below follows that chart, with the two later changes from Dexter's product bulletins added. Each Dexter cup and cone set is one cone and one cup.
| Brake size and hub | Axle capacity | Inner cone / cup | Outer cone / cup | Dexter cup and cone sets |
|---|---|---|---|---|
| 7 in. x 1-1/4 in., 4 or 5 bolt | 2,000 lb. | L44649 / L44610 | L44649 / L44610 | K71-306-00, two per hub |
| 10 in. x 1-1/2 in., 4 or 5 bolt | 2,800 lb. and 3,000 lb. | LM67048 / LM67010 | L44649 / L44610 | Inner K71-307-00, outer K71-306-00 |
| 10 in. x 2-1/4 in., 4, 5 or 6 bolt | 3,500 lb. and 4,000 lb. | L68149 / L68111 | L44649 / L44610 | Inner K71-390-00, outer K71-306-00 |
| 10 in. x 2-1/4 in., 6 bolt, built before June 2022 | 4,400 lb. | L68149 / L68111 | LM67048 / LM67010 | Inner K71-390-00, outer K71-307-00 |
| 10 in. x 2-1/4 in., 6 bolt, after June 2022 (Product Bulletin 463) | 4,400 lb. | L68149 / L68111 | L68149 / L68111 | K71-390-00, two per hub |
| 12 in. x 2 in., 6 bolt, older 5,200 lb. hub | 5,200 lb. | 25580 / 25520 | LM67048 / LM67010 | Inner K71-308-00, outer K71-307-00 |
| 12 in. x 2 in., 6 bolt, 6,000 lb. hub on 5,200 lb. axles built since 2023 (Product Bulletin 479), and 6,000 lb. axles | 5,200 lb. and 6,000 lb. | 25580 / 25520 | 15123 / 15245 | Inner K71-308-00, outer K71-309-00 |
| 12 in. x 2 in., 5 bolt demountable | 7,000 lb. | 25580 / 25520 | 15123 / 15245 | Inner K71-308-00, outer K71-309-00 |
| 12 in. x 2 in., 8 bolt | 6,000 lb. and 7,000 lb. | 25580 / 25520 | 14125A / 14276 | Inner K71-308-00, outer K71-310-00 |
| 12-1/4 in. x 2-1/2 in. or 12-1/4 in. x 3-3/8 in., 8 bolt | 7,200 lb. and 8,000 lb. | 25580 / 25520 | 02475 / 02420 | Inner K71-308-00, outer K71-415-00 |
Dexter also sells a 2,000 lb. set for hubs on a 1 in. spindle, the K71-715-00 kit with L44643 cones and L44610 cups. See all Dexter sets in Dexter Bearing Kits.
Two Dexter changes to check before you order
4,400 lb. hubs built after June 2022
Dexter Product Bulletin 463 (July 18, 2022) redesigned the 4,400 lb. wheel end with a new spindle, a new hub-drum and a new bearing set. The new spindle uses the same size bearing at both ends: an L68149 cone and L68111 cup inner and outer. Hubs built before June 2022 use the L68149 / L68111 inner bearing with an LM67048 / LM67010 outer bearing. Dexter says the old and new designs are not interchangeable and that you should find the hub-drum casting number before any service work. The bulletin lists hub-drum 008-498-05 for the new design and 008-407-05 for the old one.
5,200 lb. axles built since 2023
Dexter Product Bulletin 479 (May 8, 2023) stopped using the 5,200 lb. hub and hub-drum in production axles. Dexter 5,200 lb. axles are now built with the 6,000 lb. hub, which uses a 15123 outer cone and 15245 outer cup in place of the LM67048 cone and LM67010 cup. The spindle and the 6 on 5-1/2 in. wheel bolt pattern did not change. Dexter's note is clear: during service, replace the outer cone or cup with like parts, because they cannot be interchanged between 5,200 lb. and 6,000 lb. hubs. Read the number on the old outer bearing before you order. Southwest Wheel builds its 5,200 lb. and 6,000 lb. axles with the heavy duty hub-drum, which uses the 15123 outer bearing.
Same spindle, different hub: why outer bearings vary
Look at the outer bearings for 5,200 lb. through 8,000 lb. hubs in the size table. The LM67048, 15123, 14125A and 02475 cones all have a 1.2500 in. bore, so all four fit the same size outer bearing seat. Their cups are all different: 2.3280 in., 2.4409 in., 2.7170 in. and 2.6875 in. outside diameter. The hub casting decides which cup it takes, and the cup decides the cone.
That is why a cone that slides onto the spindle may still be the wrong part. Always match the cone to the cup that is actually in the hub, or replace both with the set the hub was built for.
Look-alike cups that are easy to mix up
Some cups are very close in size. The LM67010 cup has a 2.3280 in. outside diameter and the L68111 cup has a 2.3612 in. outside diameter, a difference of about 1/32 in. Both show up on 3,500 lb. to 5,200 lb. hubs. The TRP catalog also lists an L68110 cup with a 2.3280 in. outside diameter, and Dexter sells two marine bearing kits for the same spindle size, one with an L68110 cup and one with an L68111 cup. If the cup number is hard to read, measure the cup or the hub bore instead of guessing.
Reading Dexter service part numbers
Dexter parts lists show its own service number next to the industry number. In the Dexter bulletins and kit lists, the cup and cone of a set usually share a base number, with the cup ending in -01 and the cone ending in -02. For example, 031-033-01 is the L68111 cup and 031-033-02 is the L68149 cone. There are exceptions: 031-031-03 is the L44643 cone, which uses the same 031-031-01 (L44610) cup as the L44649 cone. When in doubt, go by the industry number in parentheses.
Heavy duty axles: 9,000 lb. to 15,000 lb.
Heavy duty hubs use larger bearings, and the 10,000 lb. class has two different sets, so check whether your axle is general duty or heavy duty. From the bearing chart in Dexter's 10,000 to 15,000 lbs. service manual:
| Axle | Inner cone / cup | Outer cone / cup |
|---|---|---|
| 9,000 lb. and 10,000 lb. general duty | 387A / 382A | 25580 / 25520 |
| 10,000 lb. heavy duty | 395S / 394A | 387A / 382A |
| 12,000 lb. and 15,000 lb. | 3984 / 3920 | 28682 / 28622 |
Notice that the 25580 / 25520 bearing is the inner bearing on 5,200 lb. to 8,000 lb. hubs and the outer bearing on 9,000 lb. and 10,000 lb. general duty hubs, and the 387A / 382A bearing moves from inner on a general duty hub to outer on a heavy duty hub. Dexter sells matched sets for the 10,000 lb. inner bearings: K71-710-00 (387A / 382A) and K71-714-00 (395S / 394A). For more on heavy duty wheel ends, see Dexter 9K to 16K Axles: What to Match Before Ordering.
How to match a bearing when the number is gone
If a number is worn off or the bearing is too damaged to read, you can still match it by size:
- Note the axle capacity and the hub. Check the axle tag, the brake size and the number of wheel studs. On a Dexter 4,400 lb. hub, find the hub-drum casting number.
- Measure the cone bore. Use calipers on the inside of the old cone, or measure the bearing seat on a clean spindle. Compare it with the cone bores in the table above, for example 1.0625 in., 1.2500 in., 1.3775 in. or 1.7500 in.
- Measure the cup. Measure the outside diameter of the old cup, or the bearing bore in the hub after the cup is out, and compare it with the cup sizes above.
- Check the other bearing in the same hub. If the inner bearing number is readable, the chart will usually tell you the outer bearing, and the reverse.
- Call with your measurements. If two sizes are close, such as the 2.3280 in. and 2.3612 in. cups, give us the axle capacity, the hub and your measurements before you order.
Bearing kits: what is included
Kits save a step when you are doing a whole wheel end, but they are not all built the same way. Check the contents before you order:
- Dexter cup and cone sets such as K71-306-00 and K71-308-00 contain one cone and one cup. A hub needs an inner set and an outer set.
- Dexter wheel end kits K71-716-00 through K71-722-00 contain the inner and outer cones and cups and a seal for one wheel end, for example the K71-717-00 kit for a 3,500 lb. hub, the K71-718-00 kit for a 4,400 lb. hub built before June 2022, the K71-719-00 kit with 25580 and 15123, the K71-720-00 kit for a 7,000 lb. 8 bolt hub and the K71-721-00 kit for 7,200 lb. and 8,000 lb. hubs.
- TruRyde pre-packaged bearing and race kits include the inner and outer bearings and races, a grease seal, a cotter pin and a tang washer, according to the TRP packaged parts brochure. They are sorted by axle capacity and seal size: 2,000 lb., 2,500 lb., 3,500 lb., 5,200 lb. with a 2.125 in. or 2.25 in. seal, 6,000 lb. with a 2.125 in. or 2.25 in. seal, and 7,000 lb. with a 2.125 in. or 2.25 in. seal. On a 5,200 lb. axle, compare the outer bearing number in the kit with the one in your hub.
- TruRyde and Timken spindle bearing kits are sorted by spindle: the TruRyde K84 and Timken KT84 for a 3,500 lb. axle, the TruRyde K42-6 and Timken KT42-6 for 5,200 lb. to 6,000 lb. 6 hole hubs, and the TruRyde K42-8 and Timken KT42-8 for 7,000 lb. 8 hole hubs.
Shop all kits in Trailer Axle Bearing Kits. Most kits that include a seal also need the right seal size; see Trailer Grease Seal Sizes.
Inspecting and replacing cups and cones
Dexter's service manual gives a simple rule for inspection: if any pitting, spalling or corrosion is present, the bearing must be replaced. Inspect the cup inside the hub as well as the cone, and replace the cone and cup together.
To replace a cup, Dexter's procedure is:
- Place the hub on a flat work surface with the cup to be replaced on the bottom side.
- Using a brass drift punch, carefully tap around the small diameter end of the cup to drive it out.
- Clean the hub bore area, then tap the new cup in with the brass drift punch. Make sure the cup is seated all the way against the retaining shoulder in the hub.
Wear safety glasses when removing or installing pressed-in parts. Keep metal chips and dirt out of the bearing cavity; Dexter warns that contaminants left there will cause early bearing failure. Dexter says to lubricate bearings every 12 months or 12,000 miles. For packing, adjustment and spindle nut steps, follow Trailer Hub Bearing Adjustment and Grease, Step by Step.
Checklist before ordering
- Axle capacity, brake size and number of wheel studs
- For a Dexter 4,400 lb. hub, the hub-drum casting number (before or after June 2022)
- For a Dexter 5,200 lb. axle, the outer bearing number on the old part
- Inner cone and cup numbers
- Outer cone and cup numbers
- Cone bore and cup outside diameter, if any number is unreadable
- Number of hubs, since each hub needs an inner and an outer bearing
- Grease seal size, if you are replacing the seal at the same time
- Whether the axle has Nev-R-Lube cartridge bearings, which use a different system
FAQ
Where is the number on a trailer wheel bearing?
On the cone, the number is on the wide face of the cone or cage. On the cup, it is on the thin edge face. Clean off the grease first so you can read every letter and digit.
What is the difference between a bearing and a race?
The bearing, or cone, is the inner part with the rollers. It slides onto the spindle. The race, or cup, is the smooth outer ring pressed into the hub that the rollers run on. They are sold under different numbers.
Can I replace just the bearing cone and keep the old cup?
No. Dexter's service manual says bearings must always be replaced in sets of a cone and a cup.
What bearings does a 3,500 lb. trailer axle use?
Most 3,500 lb. trailer hubs use an L68149 cone and L68111 cup inner bearing and an L44649 cone and L44610 cup outer bearing. Dexter's chart lists these for its 10 in. x 2-1/4 in. brake hubs, and the TruRyde hub chart and the Lippert catalog list the same pair for 3,500 lb. hubs.
Why are my old 5,200 lb. outer bearings different from the new ones?
Dexter Product Bulletin 479 moved 5,200 lb. production axles to the 6,000 lb. hub in 2023. Those hubs use a 15123 cone and 15245 cup outer bearing. Older 5,200 lb. hubs use an LM67048 cone and LM67010 cup. They do not interchange, so replace the outer bearing with the same number that came out.
My Dexter 4,400 lb. hub has the same bearing at both ends. Is that right?
Yes, if it was built after June 2022. Dexter Product Bulletin 463 changed the 4,400 lb. wheel end to use an L68149 cone and L68111 cup at both the inner and outer positions. Older 4,400 lb. hubs use an LM67048 / LM67010 outer bearing. Check the hub-drum casting number to be sure.
Do TruRyde and Timken bearings with the same number fit the same hub?
Yes. The industry number describes the size, so a TruRyde or Timken cone or cup with the same number fits the same spindle and hub. Install the cone and cup as a set.
Does a bearing kit include the races?
It depends on the kit. Dexter cup and cone sets have one cone and one cup. Dexter wheel end kits and TruRyde pre-packaged bearing and race kits include inner and outer cones and cups plus a seal. Check the kit contents before you order separate cups.
Do Nev-R-Lube hubs use these bearing numbers?
No. Nev-R-Lube bearings are opposed tapered roller cones sealed inside a one piece double cup, and they are replaced as a cartridge. See Nev-R-Lube vs E-Z Lube vs Standard Dexter Bearings.
References
- TRP International, LLC. Axle, Suspension and Frame Components catalog (2026): Bearings, Caps and Seals, Tapered Roller Bearings.
- TRP International, LLC. TruRyde hub chart: inner and outer race and bearing by hub group.
- TRP International, LLC. TruRyde Packaged Parts brochure (2026): Bearing and Race Kits.
- Dexter Axle. 2,000 to 8,000 lbs. Axle Operation Maintenance Service Manual: Hubs, Drums and Bearings, Bearing Inspection, Bearing Lubrication, and Bearing Replacement Chart.
- Dexter Axle. 10,000 to 15,000 lbs. Axle Operation Maintenance Service Manual: bearing replacement chart.
- Dexter Axle. Parts and Kits catalog: Hub Components, Bearing Kits.
- Dexter Axle Product Bulletins #364 (wheel bearing kits), #441 (D30 obsolescence), #457 (tapped idler hubs), #463 (D44 wheel-end system redesign), and #479 (5,200 lbs. hub and hub-drum obsolescence).
- Lippert. Premium Axle Parts catalog: Bearing Kits, Bearings, and Races.
Related guides
- Trailer Grease Seal Sizes: Double Lip vs Triple Lip and How to Match a Seal by Number
- Trailer Hub Bearing Adjustment and Grease, Step by Step
- Nev-R-Lube vs E-Z Lube vs Standard Dexter Bearings
- How to Identify Your Old Trailer Axle and Order a Dexter Replacement
- Trailer Axle Terms: A Plain-English Glossary
- Dexter 9K to 16K Axles: What to Match Before Ordering
Find the right bearings for your trailer hub
Have your axle capacity, brake size, wheel stud count and the numbers off your old cones and cups ready when you shop or call. Southwest Wheel has supplied trailer parts for 107 years, and we can help you match a bearing by number or by measurement.
Shop Bearings for Trailer Hubs and Drums
Need the cups too? See Races for Trailer Hubs and Drums, Trailer Axle Bearing Kits or Dexter Bearing Kits. Replacing seals at the same time? See Seals for Trailer Hubs and Drums.
Call Southwest Wheel at 1-800-866-3336.
Southwest Wheel - Your Trailers Best Friend Since 1919.






















