Updating...

Trailer Hub Size Chart by Axle Capacity: 2,000 to 8,000 lb.

A trailer hub is the part the wheel bolts to, and it rides on two tapered roller bearings on the axle spindle. The hub has to match four things: the axle's weight rating, the number of studs and the circle they sit on, the brake size, and the bearings and seal inside. Get one of those wrong and the hub will not fit, or it will fit and not carry the load.

This guide is a size chart for trailer hubs from 2,000 lb. axles up to 8,000 lb. axles. It shows the brake size, bolt pattern, bearings and seal that go with each rating, explains the Dexter changes that affect which hub you get, and lists the hubs, hub and drum sets, bearing kits and seals we stock for each size. It draws on Dexter's 2,000 to 8,000 lb. axle catalog, Dexter product bulletins, the TruRyde and DeeMaxx hub charts, Lippert's axle parts catalog and our listings. Use it as an overview, not a substitute for the instructions that came with your axle and parts.

Key takeaways

  • Hubs are sized by axle weight rating. A hub for a 3,500 lb. axle will not fit a 5,200 lb. axle, because the spindle, bearings and seal are different sizes.
  • The brake drum size is the quickest clue. 7 in. drums go with 2,000 to 2,200 lb. axles, 10 in. drums with 3,500 and 4,400 lb. axles, 12 in. drums with 5,200 to 7,000 lb. axles, and 12-1/4 in. drums with 7,200 and 8,000 lb. axles.
  • Lug count alone does not tell you the rating. A 6 on 5-1/2 in. hub can sit on a 3,500 lb. axle (the smaller spindle), a 4,400 lb. axle or a 5,200 to 6,000 lb. axle. Match the bearings and seal too.
  • The bearing numbers tell you the most. Read the number off the bearing cone and match it to the chart below. See How to Read a Tapered Roller Bearing Number and Match the Cup and Cone on a Trailer Hub for how to read the numbers.
  • Two Dexter changes matter. Since June 2022 the 4,400 lb. axle has a different spindle and hub that do not swap with the older ones. A 5,200 lb. axle can take two hubs on the same spindle: a light duty hub with an LM67048 outer bearing, and a heavy duty hub with a 15123 outer bearing and 15245 cup. We use the heavy duty hub.
  • Replace bearings with the same type that came out, and always fit a new grease seal.

Terms used in this guide

  • Hub: The part the wheel bolts to. A hub rides on the axle spindle on two bearings. A brake hub has a drum for the brake shoes to press against; an idler hub has no drum and goes on an axle with no brakes.
  • Hub and drum: A hub with the brake drum cast into it, used on axles with brakes.
  • Bolt circle (bolt pattern): The number of wheel studs and the diameter of the circle they sit on, such as 5 on 4-1/2 in. or 8 on 6-1/2 in.
  • Brake size: Drum diameter by brake shoe width, such as 10 in. x 2-1/4 in. or 12 in. x 2 in.
  • Bearing cone and cup: A tapered roller bearing has an inner part called the cone (the rollers and the ring they ride on) and an outer ring called the cup, or race, that is pressed into the hub. The cone and cup are sold together as a matched set.
  • Inner and outer bearing: The inner bearing sits behind the grease seal, closest to the trailer. The outer bearing sits under the grease cap, closest to the wheel. They are usually different sizes.
  • Grease seal: The seal behind the inner bearing that keeps grease in and water out. Its inside diameter has to match the spindle.
  • Pre-greased hub kit: A hub or hub and drum with the bearings and seal already installed and packed with grease.

Trailer hub size chart by axle capacity

This chart is for standard Dexter-style trailer hubs, from Dexter's catalog and product bulletins, the TruRyde hub chart and Lippert's parts catalog. Where Dexter's own bulletin and its catalog disagree, the bulletin is used. Bearing numbers are for the cone, with the matching cup number next to it.

Axle capacity Brake size Bolt patterns Inner bearing (cone / cup) Outer bearing (cone / cup) Grease seal
2,000 to 2,200 lb. 7 in. x 1-1/4 in. 4 on 4 in.; 5 on 4-1/2 in. L44649 / L44610 (a smaller L44643 bearing is used on TruRyde's lightest spindle) L44649 / L44610 1.50 in. inside diameter (1.25 in. on the lightest spindle)
3,500 lb. 10 in. x 2-1/4 in. 5 on 4-1/2, 5 on 4-3/4, 5 on 5 and 5 on 5-1/2 in.; 6 on 5-1/2 in. also offered L68149 / L68111 L44649 / L44610 1.72 in. inside diameter x 2.565 in. outside diameter
4,400 lb. 10 in. x 2-1/4 in. 6 on 5-1/2 in. L68149 / L68111 After June 2022: L68149 / L68111. Before June 2022: LM67048 / LM67010 1.72 in. inside diameter x 2.565 in. outside diameter
5,200 lb. 12 in. x 2 in. 6 on 5-1/2 in. (Dexter notes 8 on 6-1/2 in. is also available) 25580 / 25520 15123 / 15245 on the heavy duty hub we use; LM67048 / LM67010 on the light duty hub 2.25 in. inside diameter (older hubs may use 2.125 in.)
6,000 lb. 12 in. x 2 in. 6 on 5-1/2 in. 25580 / 25520 15123 / 15245 2.25 in. inside diameter
7,000 lb. 12 in. x 2 in. 8 on 6-1/2 in. 25580 / 25520 14125A / 14276 on the standard 8 stud hub (15123 / 15245 on Dexter's demountable hub) 2.25 in. inside diameter
7,200 lb. 12-1/4 in. x 2-1/2 in. 8 on 6-1/2 in. 25580 / 25520 02475 / 02420 Unitized oil seal, 2.250 in. inside diameter x 3.376 in. outside diameter
8,000 lb. 12-1/4 in. x 2-1/2 in. or 12-1/4 in. x 3-3/8 in. 8 on 6-1/2 in. 25580 / 25520 02475 / 02420 Unitized oil seal, 2.250 in. inside diameter x 3.376 in. outside diameter

The bearing numbers line up with the spindle sizes. From our listings, the L44643 cone has a 1 in. bore, the L44649 cone 1-1/16 in., the L68149 cone 1-3/8 in., the LM67048, 15123 and 14125A cones 1-1/4 in., and the 25580 cone 1-3/4 in. A cone only fits a spindle journal of that size, which is why a hub for one rating will not go on another.

Bolt pattern: which hubs come in which circle

The bolt circle has to match the wheel as well as the hub, so write it down before you order a hub or a wheel. Trailer Wheel Load Ratings and Hub Pilot vs Stud Pilot Wheels covers wheel load ratings and the hub pilot.

Bolt circle Where it is used
4 on 4 in. 2,000 to 2,200 lb. axles
5 on 4-1/2 in. 2,000 to 2,200 lb. and 3,500 lb. axles, the most common trailer bolt pattern
5 on 4-3/4 in., 5 on 5 in., 5 on 5-1/2 in. 3,500 lb. axles
6 on 5-1/2 in. 3,500 lb. (offered), 4,400 lb., 5,200 lb. and 6,000 lb. axles
8 on 6-1/2 in. 7,000, 7,200 and 8,000 lb. axles

Dexter's wheel guidance (Product Bulletin #409) is to match the bolt circle, hub pilot and offset of the wheel to the axle, make sure the wheel is rated for the load, and follow the wheel maker's torque instructions.

How to tell which hub you have

  1. Find the axle rating. Look for the axle tag or label on the tube. For Dexter axles see How to Identify Your Old Trailer Axle and Order a Dexter Replacement, and for Lippert axles see How to Identify a Lippert Spring Axle From Its Tag.
  2. Check the brake size. The drum diameter (7, 10, 12 or 12-1/4 in.) narrows the rating right away. An idler hub has no drum, so use the other clues.
  3. Count the studs and note the bolt circle. Check it against the chart above.
  4. Read the bearing numbers. The number is stamped on the cone and the cup. Match both to the chart. How to Read a Tapered Roller Bearing Number and Match the Cup and Cone on a Trailer Hub walks through it.
  5. Check the seal. The seal size is printed in our listings, and Trailer Grease Seal Sizes: Double Lip vs Triple Lip and How to Match a Seal by Number explains how to match a seal by its number.
  6. For a Dexter 4,400 lb. or 5,200 lb. axle, check the age. See the next section.

Dexter changes that affect which hub you need

  • 4,400 lb. axle (Product Bulletin #463, July 2022). Dexter redesigned the wheel end with a new spindle, hub and drum, and bearing set. The new spindle is a parallel design that takes a larger bearing of the same size at both ends. The hub and drum are marked with a casting number, 008-498-05 for the new design and 008-407-05 for the old one. The two designs are not interchangeable, so find the casting number before you buy parts. We stock both: Dexter pre-greased 6 on 5-1/2 in. hub and drum for 4,400 lb. axles, after June 2022 and Dexter 4,400 lb. hub and drum kit, before June 2022. Bearings for the newer design are the L68149 cone and L68111 cup (K71-390-00) at both ends, and the older design uses bearing and seal kit with L68149 and LM67048, K71-718-00.
  • 5,200 lb. axle (Product Bulletin #479, May 2023). Two hubs fit the same 5,200 lb. spindle and the same 6 on 5-1/2 in. bolt pattern, so the wheels still fit. The light duty hub uses an LM67048 cone and LM67010 cup as its outer bearing. The heavy duty hub, the one we use, uses a 15123 cone and 15245 cup, the same outer bearing as a 6,000 lb. hub. Bulletin #479 says Dexter now builds its 5,200 lb. axles with that heavier hub. The two outer bearings cannot be swapped, so replace them with the same type that came out. We stock the heavy duty outer as the TruRyde 15123 bearing and the TruRyde 15245 race.
  • 3,000 lb. axle (Product Bulletin #441, May 2021). Dexter discontinued its 10 in. x 1-1/2 in. 3,000 lb. axle. Its hub and brake do not interchange with the 3,500 lb. 10 in. x 2-1/4 in. hub. If you have one, replace the hub only with a part made for the 3,000 lb. axle.
  • 7,200 to 7,500 lb. axles (Product Bulletin #460, May 2022). Dexter stopped offering 1/2 in. wheel studs on these axles' hub and drum. Service parts come with 9/16 in. or 5/8 in. studs, so check wheel fit and torque when you change studs.
  • Bearing kits by rating (Product Bulletin #364). Dexter's prepackaged wheel bearing kits are organized by axle rating: 2,200, 3,500, 4,400, 6,000 (6 bolt), 6,000 and 7,000 (8 bolt), and 7,200 and 8,000 lb.

2,000 to 2,200 lb. hubs

These are the lightest hubs: 7 in. brakes, or no brakes on an idler axle, with 4 on 4 in. or 5 on 4-1/2 in. patterns. TruRyde offers them on two spindle sizes, a smaller one with a 1 in. bore bearing and a larger one with a 1-1/16 in. bore bearing (TruRyde names them BT8 and BT9). Match the hub to the spindle, not just to the bolt pattern.

3,500 lb. hubs

The 3,500 lb. hub is one of the most common trailer hubs: 10 in. x 2-1/4 in. brakes, an L68149 inner and an L44649 outer bearing, and most often 5 on 4-1/2 in. studs. It also comes in 5 on 4-3/4, 5 on 5 and 5 on 5-1/2 in., and Dexter offers a 6 on 5-1/2 in. version. 3,500 lb. vs 5,200 lb. Trailer Axle: Which One Do You Need compares this axle with the 5,200 lb. size.

4,400 lb. hubs

The 4,400 lb. axle uses the same 10 in. x 2-1/4 in. brake as a 3,500 lb. axle but a 6 on 5-1/2 in. hub on a 3 in. tube, with a larger outer bearing than the 3,500 lb. axle. Because of the 2022 redesign described above, check the hub casting number or the date of the axle before ordering. See K08-498-1G for newer axles or K08-407-90 for older axles.

5,200 and 6,000 lb. hubs

These share one spindle, a 6 on 5-1/2 in. pattern and 12 in. x 2 in. brakes. The 25580 inner bearing is the same as on the 7,000 and 8,000 lb. hubs. The outer bearing is the one that changes: we use the heavy duty hub, with a 15123 cone and 15245 cup. The light duty hub uses an LM67048 outer bearing instead.

7,000 lb. hubs

The 7,000 lb. hub keeps the 12 in. x 2 in. brake of the 5,200 lb. hub but moves to eight studs on a 6-1/2 in. circle. Most 7,000 lb. hubs use a 25580 inner bearing and a 14125A outer bearing with a 14276 cup.

7,200 and 8,000 lb. hubs

These use a larger 12-1/4 in. brake, eight studs on a 6-1/2 in. circle, a 25580 inner and a 02475 outer bearing, and a unitized seal. They come in grease and oil versions, with 9/16 in. or 5/8 in. studs. These heavy hubs are close in size, so go by the axle tag and the hub casting number.

Dexter also makes Nev-R-Lube hubs with sealed bearings for 5,200 to 8,000 lb. axles. They are a different design from a standard hub, so see Nev-R-Lube vs E-Z Lube vs Standard Dexter Bearings before swapping one.

Hub only, hub and drum, or hub with parts?

  • Hub only or hub and drum only: The casting and studs, sold alone. You supply bearings, seal, grease cap and nuts.
  • Hub with parts (idler hub): A hub with its bearings, seal, cap and spindle hardware, for an axle without brakes.
  • Hub and drum with parts: The same, with a brake drum, for an axle with brakes.
  • Pre-greased kit: Dexter introduced pre-greased hub and hub and drum kits for 2,200 to 7,000 lb. axles in 2022, with bearings and seal installed and packed. TruRyde and Lippert sell similar kits.

Our trailer hubs with parts category has all of these. For brakes to go with a new hub, see How to Choose a TruRyde Drum Brake Kit: Electric vs Hydraulic, Capacity and Axle Count.

Checklist before you order

  • Axle rating, from the tag or label.
  • Brake size, or confirm it is an idler hub.
  • Stud count and bolt circle, and the wheel you will mount.
  • Bearing numbers on the cone and cup, and the grease seal size.
  • For Dexter 4,400 lb. and 5,200 lb. axles, the age or the hub casting number.
  • Grease or oil, and the stud size on 7,000 lb. and heavier hubs.

If you are replacing a whole axle, our pre-configured Dexter axles and custom built Dexter axles come with matching hubs, and Build a Complete Dexter Trailer Axle walks through building one.

Safety note

Wheel bearings and brakes are safety parts. Replace both bearings and the seal together, clean the drum and brake parts, and check the brakes after any hub work. Tighten wheel nuts to the wheel maker's torque in the recommended sequence, and recheck after the first miles. If you are unsure about a part, call us before you order.

FAQ

How do I know what size hub my trailer has?

Start with the axle tag for the rating, then the brake drum size, the stud count and bolt circle, and the bearing numbers on the cone and cup. The chart above ties these together.

What is the most common trailer hub?

One of the most common is a 5 on 4-1/2 in. hub for a 3,500 lb. axle, with a 10 in. x 2-1/4 in. brake, an L68149 inner and an L44649 outer bearing.

Is a 6 lug hub always for a 5,200 lb. axle?

No. A 6 on 5-1/2 in. hub is also made for 3,500 lb. axles, 4,400 lb. axles and 6,000 lb. axles. Check the bearings and seal as well.

What is the difference between a 5,200 lb. and a 6,000 lb. hub?

Two hubs fit the same 5,200 lb. spindle. The light duty hub uses an LM67048 outer bearing. The heavy duty hub, which is also the 6,000 lb. hub and the one we use, uses a 15123 cone and 15245 cup. The spindle and bolt pattern are the same. Dexter has built its 5,200 lb. axles with the heavy duty hub since 2023.

What bearings go in a 7,000 lb. trailer hub?

Most 7,000 lb. hubs use a 25580 inner bearing and a 14125A outer bearing with a 14276 cup. Dexter's demountable 7,000 lb. hub uses a 15123 outer bearing instead, so check your hub.

Can I put a 3,500 lb. hub on a 5,200 lb. axle?

No. The spindle is larger on the 5,200 lb. axle, so the bearings, seal and hub are all different sizes.

Do I need to replace the seal when I replace bearings?

Yes. Fit a new grease seal whenever the hub comes off. See Trailer Hub Bearing Adjustment and Grease, Step by Step for how to adjust and grease the bearings after you reassemble the hub.

Are Dexter, TruRyde and Lippert hubs interchangeable?

For a given axle rating the bearing numbers are the same across brands, so the spindle size matches. Even so, check the bolt circle, stud size, brake size and the listing for your axle before you swap brands.

References

  • Dexter Axle. Light Duty Catalog, 600 to 8,000 lbs. axle capacity (LIT-122-00, 2020.05): hub group pages for 1,000 to 2,200 lbs., 2,300 to 4,000 lbs., 4,100 to 6,000 lbs. and 5,500 to 7,000 lbs. capacity; 7,200 and 8,000 lb. hub groups; Nev-R-Lube information.
  • Dexter Axle. Product Bulletin #364, Wheel Bearing Kits (March 29, 2013).
  • Dexter Axle. Product Bulletin #441, D30 Obsolescence (May 28, 2021).
  • Dexter Axle. Product Bulletin #460, Obsolete 1/2 in. Stud Option for 7,200 to 7,500 lb. Axles (May 13, 2022).
  • Dexter Axle. Product Bulletin #463, D44 Wheel-end System Redesign (July 18, 2022).
  • Dexter Axle. Product Bulletin #464, Pre-Greased Hub and Hub-Drum Kits (August 1, 2022).
  • Dexter Axle. Product Bulletin #479, 5,200 lbs. Hub and Hub-Drum Obsolescence - Axle Production (May 8, 2023).
  • Dexter Axle. Product Bulletin #409, Wheel Attachment and Torque Requirements (October 14, 2019).
  • TruRyde. Hub chart (bolt circle, bearing, seal and spindle by hub).
  • Lippert. Premium axle parts catalog: hub sizes and wheel bearing kit chart by capacity.

Related guides

Find the right trailer hub

Have your axle rating, brake size, bolt circle and bearing numbers ready when you shop or call. Southwest Wheel has supplied trailer parts for 107 years, and we can help you match a hub with the bearings, seals, brakes and wheels that go with it.

Shop Trailer Hubs With Parts

Need the axle too? See pre-configured Dexter trailer axles or custom built Dexter trailer axles.

Call Southwest Wheel at 1-800-866-3336.

Southwest Wheel - Your Trailers Best Friend Since 1919.

 
Sign Up For Special Offers and News!

Get 5% off your first purchase , information on newest offers, and useful tips on how to get the most out of our services.

Valid once per customer on first purchase only. Not combinable with other offers or past orders.
 
Loading...